## tisdag 26 november 2013

### Cinema Releases 2013-11-26

Movies I've seen at the cinema or think is interesting to see ...

Filmer jag sett på bio eller tycker verkar intressanta att se...

20131115 The Councellor - 20th century fox
Official - www.thecouncellormovie.com/
20131115 MUD - Lionsgate
Official - http://mud-themovie.com
20131120 Hunger Games: Catching fire – Lionsgate
Official - http://www.thehungergamesexplorer.com/us/epk/hunger-games/
20131129 Carrie - Metro Goldwym Mayer
Official - www.carrie-movie.com
20131206 Battle of the Year - Sony pictures
Official - www.sonypictures.com/movies/battleoftheyear/
20131206 Escape plan - Lionsgate
Official - http://escapeplanmovie.com/
20131211 The Hobbit: The Desolation of Smaug - Warner Bros Company
Official - http://www.thehobbit.com/

# Circuit Switched Data

Circuit Switched Data (CSD) is the original form of data transmission developed for the time division multiple access (TDMA)-basedmobile phone systems like Global System for Mobile Communications (GSM). CSD uses a single radio time slot to deliver 9.6 kbit/sdata transmission to the GSM Network and Switching Subsystem where it could be connected through the equivalent of a normalmodem to the Public Switched Telephone Network (PSTN) allowing direct calls to any dial-up service. For backwards compatibility theIS-95 standard also supports CDMA Circuit Switched Data however unlike TDMA there are no time slots, all CDMA radios can be active all the time to deliver up to 14.4 kbit/s data transmission speeds. With the evolution of CDMA to CDMA2000 and 1xRTT the use of IS-95 CDMA Circuit Switched Data declined in favour of the faster data transmission speeds available with the newer technologies.
Prior to CSD, data transmission over mobile phone systems was done by using a modem, either built into the phone or attached to it. Such systems were limited by the quality of the audio signal to 2.4 kbit/s or less. With the introduction of digital transmission in TDMA-based systems like GSM, CSD provided almost direct access to the underlying digital signal, allowing for higher speeds. At the same time, the speech oriented audio compression used in GSM actually meant that data rates using a traditional modem connected to the phone would have been even lower than with older analog systems.
A CSD call functions in a very similar way to a normal voice call in a GSM network. A single dedicated radio time slot is allocated between the phone and the base station. A dedicated "sub-time slot" (16 kbit/s) is allocated from the base station to the transcoder, and finally another time slot (64 kbit/s) is allocated from the transcoder to the Mobile Switching Centre (MSC).
At the MSC, it is possible to use a modem to convert to an "analog" signal, though this will typically actually be encoded as a digitalpulse-code modulation (PCM) signal when sent from the MSC. It is also possible to directly use the digital signal as an Integrated Services Digital Network (ISDN) data signal and feed it into the equivalent of a remote access server.
GSM data transmission has advanced since the introduction of CSD:

## Availability

The T-Mobile system is area/city specific. It works in Denver, ColoradoSavannah, Georgia, Washington, DC, and Miami, FL and Las Vegas into SoCal roaming onto Cingular. There is no service in Sarasota, Florida or anywhere in Texas. Fax services required a second number for an additional \$10/mo.
The AT&T Mobility GSM EDGE network supports CSD in legacy Cingular and AT&T Wireless footprint areas. It is not generally available but can be provisioned for selected customers with specific needs requiring the service.
Currently in Australia, CSD is only available on Mobile Plans with VodafoneOptus and Telstra, however Telstra is in the process of shutting down their CSD network as of the 4th May 2010.[1]
In the UK CSD is available with all of the mobile networks but may require activation by the networks customer service team. CSD is commonly used in the UK for early smart metering deployments and as such there are no real plans to decommission or remove access to this part of the 2G network.[citation needed]

# IS-95

Samsung cdmaOne mobile phonedisassembled
Interim Standard 95 (IS-95) is the first CDMA-based digital cellular standard by Qualcomm. The brand name for IS-95 is cdmaOne. IS-95 is also known as TIA-EIA-95.
It is a 2G mobile telecommunications standard that uses CDMA, a multiple access scheme for digital radio, to send voice, data and signaling data (such as a dialed telephone number) between mobile telephones and cell sites.
CDMA or "code division multiple access" is a digital radio system that transmits streams ofbits (PN codes). CDMA permits several radios to share the same frequencies. Unlike TDMA"time division multiple access", a competing system used in 2G GSM, all radios can be active all the time, because network capacity does not directly limit the number of active radios. Since larger numbers of phones can be served by smaller numbers of cell-sites, CDMA-based standards have a significant economic advantage over TDMA-based standards, or the oldest cellular standards that used frequency-division multiplexing.
In North America, the technology competed with Digital AMPS (IS-136, a TDMA technology). It is now being supplanted by IS-2000(CDMA2000), a later CDMA-based standard.

## Protocol revisions

cdmaOne's technical history is reflective of both its birth as a Qualcomm internal project, and the world of then-unproven competing digital cellular standards under which it was developed. The term IS-95 generically applies to the earlier set of protocol revisions, namely P_REV's one through five.
P_REV=1 was developed under an ANSI standards process with documentation reference J-STD-008. J-STD-008, published in 1995, was only defined for the then-new North American PCS band (Band Class 1, 1900 MHz). The term IS-95 properly refers to P_REV=1, developed under the Telecommunications Industry Association (TIA) standards process, for the North American cellular band (Band Class 0, 800 MHz) under roughly the same time frame. IS-95 offered interoperation (including handoff) with the analog cellular network. For digital operation, IS-95 and J-STD-008 have most technical details in common. The immature style and structure of both documents are highly reflective of the "standardizing" of Qualcomm's internal project.
P_REV=2 is termed Interim Standard 95A (IS-95A). IS-95A was developed for Band Class 0 only, as in incremental improvement over IS-95 in the TIA standards process.
P_REV=3 is termed Technical Services Bulletin 74 (TSB-74). TSB-74 was the next incremental improvement over IS-95A in the TIA standards process.
P_REV=4 is termed Interim Standard 95B (IS-95B) Phase I, and P_REV=5 is termed Interim Standard 95B (IS-95B) Phase II. The IS-95B standards track provided for a merging of the TIA and ANSI standards tracks under the TIA, and was the first document that provided for interoperation of IS-95 mobile handsets in both band classes (dual-band operation). P_REV=4 was by far the most popular variant of IS-95, with P_REV=5 only seeing minimal uptake in South Korea.
P_REV=6 and beyond fall under the CDMA2000 umbrella. Besides technical improvements, the IS-2000 documents are much more mature in terms of layout and content. They also provide backwards-compatibility to IS-95.

## Protocol details

cdmaOne network structure
The IS-95 standards describe an air interface, a set of protocols used between mobile units and the network. IS-95 is widely described as a three-layer stack, where L1 corresponds to the physical (PHY) layer, L2 refers to the Media Access Control (MAC) and Link-Access Control (LAC) sublayers, and L3 to the call-processing state machine.

### Physical layer

IS-95 defines the transmission of signals in both the forward (network-to-mobile) and reverse (mobile-to-network) directions.
In the forward direction, radio signals are transmitted by base stations (BTS's). Every BTS is synchronized with a GPS receiver so transmissions are tightly controlled in time. All forward transmissions are QPSK with a chip rate of 1,228,800 per second. Each signal is spread with a Walsh code of length 64 and a pseudo-random noise code (PN code) of length ${2}^{15}$, yielding a PN roll-over period of $\frac{80}{3}$ ms.
For the reverse direction, radio signals are transmitted by the mobile. Reverse link transmissions are OQPSK in order to operate in the optimal range of the mobile's power amplifier. Like the forward link, the chip rate is 1,228,800 per second and signals are spread withWalsh codes and the pseudo-random noise code, which is also known as a Short Code.

Every BTS dedicates a significant amount of output power to a pilot channel, which is an unmodulated PN sequence (in other words, spread with Walsh code 0). Each BTS sector in the network is assigned a PN offset in steps of 64 chips. There is no data carried on the forward pilot. With its strong autocorrelation function, the forward pilot allows mobiles to determine system timing and distinguish different BTS's for handoff.
When a mobile is "searching", it is attempting to find pilot signals on the network by tuning to particular radio frequencies, and performing a cross-correlation across all possible PN phases. A strong correlation peak result indicates the proximity of a BTS.
Other forward channels, selected by their Walsh code, carry data from the network to the mobiles. Data consists of network signaling and user traffic. Generally, data to be transmitted is divided into frames of bits. A frame of bits is passed through a convolutional encoder, adding forward error correction redundancy, generating a frame of symbols. These symbols are then spread with the Walsh and PN sequences and transmitted.
BTSs transmit a sync channel spread with Walsh code 32. The sync channel frame is $\frac{80}{3}$ ms long, and its frame boundary is aligned to the pilot. The sync channel continually transmits a single message, the Sync Channel Message, which has a length and content dependent on the P_REV. The message is transmitted 32 bits per frame, encoded to 128 symbols, yielding a rate of 1200 bit/s. The Sync Channel Message contains information about the network, including the PN offset used by the BTS sector.
Once a mobile has found a strong pilot channel, it listens to the sync channel and decodes a Sync Channel Message to develop a highly accurate synchronization to system time. At this point the mobile knows whether it is roaming, and that it is "in service".
BTSs transmit at least one, and as many as seven, paging channels starting with Walsh code 1. The paging channel frame time is 20 ms, and is time aligned to the IS-95 system (i.e. GPS) 2-second roll-over. There are two possible rates used on the paging channel: 4800 bit/s or 9600 bit/s. Both rates are encoded to 19200 symbols per second.
The paging channel contains signaling messages transmitted from the network to all idle mobiles. A set of messages communicate detailed network overhead to the mobiles, circulating this information while the paging channel is free. The paging channel also carries higher-priority messages dedicated to setting up calls to and from the mobiles.
When a mobile is idle, it is mostly listening to a paging channel. Once a mobile has parsed all the network overhead information, itregisters with the network, then optionally enters slotted-mode. Both of these processes are described in more detail below.

#### Forward traffic channels

The Walsh space not dedicated to broadcast channels on the BTS sector is available for traffic channels. These channels carry the individual voice and data calls supported by IS-95. Like the paging channel, traffic channels have a frame time of 20ms.
Since voice and user data are intermittent, the traffic channels support variable-rate operation. Every 20 ms frame may be transmitted at a different rate, as determined by the service in use (voice or data). P_REV=1 and P_REV=2 supported rate set 1, providing a rate of 1200, 2400, 4800, or 9600 bit/s. P_REV=3 and beyond also provided rate set 2, yielding rates of 1800, 3600, 7200, or 14400 bit/s.
For voice calls, the traffic channel carries frames of vocoder data. A number of different vocoders are defined under IS-95, the earlier of which were limited to rate set 1, and were responsible for some user complaints of poor voice quality. More sophisticated vocoders, taking advantage of modern DSPs and rate set 2, remedied the voice quality situation and are still in wide use in 2005.
The mobile receiving a variable-rate traffic frame does not know the rate at which the frame was transmitted. Typically, the frame is decoded at each possible rate, and using the quality metrics of the Viterbi decoder, the correct result is chosen.
Traffic channels may also carry circuit-switch data calls in IS-95. The variable-rate traffic frames are generated using the IS-95 Radio Link Protocol (RLP). RLP provides a mechanism to improve the performance of the wireless link for data. Where voice calls might tolerate the dropping of occasional 20 ms frames, a data call would have unacceptable performance without RLP.
Under IS-95B P_REV=5, it was possible for a user to use up to seven supplemental "code" (traffic) channels simultaneously to increase the throughput of a data call. Very few mobiles or networks ever provided this feature, which could in theory offer 115200 bit/s to a user.
Block Interleaver
After convolution coding and repetition, symbols are sent to a 20 ms block interleaver, which is a 24 by 16 array.

#### Capacity

IS-95 and its use of CDMA techniques, like any other communications system, have their throughput limited according to Shannon's theorem. Accordingly, capacity improves with SNR and bandwidth. IS-95 has a fixed bandwidth, but fares well in the digital world because it takes active steps to improve SNR.
With CDMA, signals that are not correlated with the channel of interest (such as other PN offsets from adjacent cellular base stations) appear as noise, and signals carried on other Walsh codes (that are properly time aligned) are essentially removed in the de-spreading process. The variable-rate nature of traffic channels provide lower-rate frames to be transmitted at lower power causing less noise for other signals still to be correctly received. These factors provide an inherently lower noise level than other cellular technologies allowing the IS-95 network to squeeze more users into the same radio spectrum.
Active (slow) power control is also used on the forward traffic channels, where during a call, the mobile sends signaling messages to the network indicating the quality of the signal. The network will control the transmitted power of the traffic channel to keep the signal quality just good enough, thereby keeping the noise level seen by all other users to a minimum.
The receiver also uses the techniques of the rake receiver to improve SNR as well as perform soft handoff.

### Layer 2

Once a call is established, a mobile is restricted to using the traffic channel. A frame format is defined in the MAC for the traffic channel that allows the regular voice (vocoder) or data (RLP) bits to be multiplexed with signaling message fragments. The signaling message fragments are pieced together in the LAC, where complete signaling messages are passed on to Layer 3.